Unofficial Stationeers Wiki Unofficial Stationeers Wiki

Kit (Furnace)

Volume	250 L
Recipe
Created With	Autolathe, Fabricator
Cost	30g Iron, 10g Copper
Logic
Logic Parameters	Open Pressure Temperature Lock Setting Reagents RatioOxygen RatioCarbonDioxide RatioNitrogen RatioPollutant RatioVolatile RatioWater Maximum Ratio ImportQuantity ImportSlotOccupant ExportQuantity ExportSlotOccupant

Furnace

Construction
Placed with	Kit (Furnace)
Placed on	Small Grid
Stage 1
Deconstruction
Deconstructed with	Hand Drill
Item received	Kit (Furnace)

Description

Used to smelt ingots and alloys using an oxygen/volatile gas mix. Ice (Oxite) and Ice (Volatiles) can be manually input directly in the furnace in order to create crude gas mixtures, or to be directly extracted as an easy trick for melting the ice.

If the contents of the furnace are ejected without reaching the required temperature and pressure for smelting, they'll come out as Reagent which can be processed in a Centrifuge to recover the raw ores.

Recipes

While smelting steel is easily achieved with ice, other recipes usually require a working piping setup. This can be done by separating gases into tanks using atmospheric units and piping individual gases through a mixer and a Pressure Regulator or a Pipe Volume Pump connected to the furnace input. Output should also be extracted and vented/recycled through a backpressure regulator to keep furnace pressure in check. The optimal gas mix that burns completely is 1 part (33.3%) oxygen to 2 parts (66.6%) volatiles, other mixes would also work but leave you with leftover oxygen or volatiles depending on the percentages used. It could also result in lower temperature if that is desired, but you could also use a volume pump with a lower fuel input setting.

Make sure to put the fuel in first, then press the activate button. Afterwards, put in the ingredients, and press the handle after you see the "will produce" while hovering over the furnace.

Item	Pressure (kPa)		Temp (K)		Temp (C)		Ingredients		Notes
	Min	Max	Min	Max	Min	Max	Ratio	Ore
Lead	100	100,000	300	100,000	26.85	99,726.85	1	Lead
Gold			600		326.85			Gold
Copper			600		326.85			Copper
Silver			600		326.85			Silver
Nickel			800		526.85			Nickel
Iron			900		626.85			Iron
Silicon			900		626.85			Silicon
Solder	300	3 500	300	2 000	26.85	1 726.85	1:1	Iron:Lead	Can be achieved by dropping 2 oxite and 1 volatile
Steel	100	100 000	600	100 000	326.85	99,726.85	3:1	Iron:Carbon(Coal)	Can easily be achieved by just dropping 1 oxite and 2 volatiles
Electrum	800	2 400	700	10 000	426.85	9726.85	1:1	Gold:Silver	Can be achieved by just dropping 1 oxite and 2 volatiles
Invar	6 000	7 000	1 200	2 000	926.85	1326.855	1:1	Iron:Nickel	Can be achieved by just dropping 4 volatiles and 2 oxite (for 50:50)
Constantan	100	10 000	1 000	1 500	1 0005	1 5005	1:1	Copper:Nickel	Can be achieved by dropping 4 oxite and 1 volatile

Some example fuel mixes

Prime	AFR	In: Mols		Result		Out: Mols
		H2	O2	Press.	Temp	O2	H2	Co2	X
100 kPa	2:1	29	14	2 135	1 953	1	3	82	33
200 kPa	2:1	59	29	4 500	2 000	1	5	169	80
200 kPa	3:1	65	21	3 400	1 900	2	26	118	52
200 kPa	4:1	72	18	3 000	1 800	1	40	99	42
200 kPa	1:1	43	43	3 493	1 917	22	2	127	59
200 kPa	1:4	17	68	1 646	1 319	63	2	50	18
300 kPa	2:1	86	42	6 850	2 109	2	7	242	115
500 kPa	2:1	143	69	11 814	2 150	3	11	400	193

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters that can be written with a Logic Writer, Batch Writer, or Integrated Circuit (IC10).

Parameter Name	Data Type	Description
Open	Boolean	Opens the Furnace, when set to 1. Closes it, when set to 0.
Activate	Boolean	Activates the Furnace, when set to 1.
Lock	Boolean	Locks the Furnace, when set to 1. Unlocks it when set to 0.
Setting	Float	(Unknown) Affects the Setting output.

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name	Data Type	Description
Open	Boolean	Returns whether the Furnace is open. (0 for no, 1 for yes)
Pressure	Float	Returns the pressure in the Furnace in kilo pascal.
Temperature	Float	Returns the temperature in the Furnace in kelvin.
Lock	Boolean	Returns whether the Furnace is locked.
Setting	Float	(Unknown) Affected by the Setting parameter.
Reagents	Float	Returns the amount of reagents (smeltable ores, not counting ice) in the Furnace, in grams.
RatioOxygen	Float	Returns a range from 0.0 to 1.0. Returns the percentage ratio of the amount of oxygen in the Furnace.
RatioCarbonDioxide	Float	Returns a range from 0.0 to 1.0. Returns the percentage ratio of the amount of carbon dioxide in the Furnace.
RatioNitrogen	Float	Returns a range from 0.0 to 1.0. Returns the percentage ratio of the amount of nitrogen in the Furnace.
RatioPollutant	Float	Returns a range from 0.0 to 1.0. Returns the percentage ratio of the amount of pollutant in the Furnace.
RatioVolatiles	Float	Returns a range from 0.0 to 1.0. Returns the percentage ratio of the amount of volatiles in the Furnace.
RatioWater	Float	Returns a range from 0.0 to 1.0. Returns the percentage ratio of the amount of water in the Furnace.
Maximum	Integer	(Unknown) Returns 100.
Ratio	Float	(Unknown) Returns 0.5.
ImportQuantity	Float	Returns the amount of items in the import slot of the Furnace, which are currently smelted, in grams.
ImportSlotOccupant	Boolean	Returns whether there is something in the import slot of the Furnace, being smelted. (0 for no, 1 for yes)
ExportQuantity	Float	Returns the amount of items in the export slot of the Furnace, in grams. (Only briefly returns a value, when the Furnace is opened and items are exported.)
ExportSlotOccupant	Boolean	Returns whether there is something in the export slot of the Furnace. (Only briefly returns a value, when the Furnace is opened and items are exported.)