Unofficial Stationeers Wiki Unofficial Stationeers Wiki

This page contains outdated information on the Atmospherics Kit, and should not be used as is. The entire page needs to be rewritten to be valid again!

Kit (Atmospherics)

Stacks	False
Recipe
Created With	Hydraulic Pipe Bender, Fabricator
Cost	10g Iron, 5g Gold, 20g Copper

Description

This kit produces the following:

• Air Conditioner
• Electrolyzer
• Filtration
• Nitrolyzer
• H2 Combustor

Air Conditioner Unit

Air Conditioner

Operation
Power Usage	Up to 7000W based on temperature difference
Construction
Placed with	Kit (Atmospherics)
Placed on	Small Grid
Stage 1
Deconstruction
Deconstructed with	Hand Drill
Item received	Kit (Atmospherics)

Description

Used to lower or raise the temperature of Gas in a pipe network. It has a range of -200 through 200 Celsius for the temperature output.

Usage

Once you have placed the Air Conditioner Unit in your desired location, there are 3 separate connections that will need to be made:

1. Input - The starting gas that is desired to be cooled or heated
2. Output - The exhausted gas after energy has been transferred to or from the Coolant in the waste pipe network
3. Waste - Connection where energy is transferred to the Coolant in the pipe network

Waste Pipe Network
A connected gas pipe network containing any desired Coolant. The Air Conditioner Unit will draw or expel heat from/to the coolant to adjust the input gas temperature to match the selected output temperature.

If the waste pipe network is below 100kPa pressure upon starting the Air Conditioning Unit, it will divert inputted gas from the output port to the waste port until the minimum 100kPa pressure threshold is met within the waste pipe network.

Cooling

Attached to the waste pipe network should be either Pipe Radiators or Medium Radiators to convect heat in a pressurized environment or radiate heat in a vacuum environment. Make the pipe network loop on back to the waste port after the radiators for slightly better efficiency.

Heating

Ensuring the temperature of the coolant is higher than the temperature of the gas you want attempting to heat will allow the Air Conditioner Unit to heat the gas being run through the input port. Attaching a Pipe Heater is a quick method of raising the temperature of the Coolant in the waste pipe network.

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters, that can be written to with a Logic Writer, Batch Writer, or Integrated Circuit (IC10). The outputs are listed in the order a Logic Writer's "VAR" setting cycles through them.

Parameter Name	Data Type	Description
Open	Boolean	Starts the Air Conditioner Unit, when set to 1. Stops it, when set to 0. (This seems to work only with Batch Writer and not with Logic Writer - tested on game ver: v0.1.1362.6552).
Mode	Integer	(Unknown) (Judging by the "Mode" output, it accepts values in the range 0-2.)
Lock	Boolean	Locks the Air Conditioner Unit, when set to 1. Unlocks it, when set to 0.
On	Boolean	Turns the Air Conditioner Unit on, when set to 1. Turns it off, when set to 0.

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name	Data Type	Description
Power	Boolean	Returns whether the Air Conditioner Unit is turned on and receives power. (0 for no, 1 for yes)
Open	Boolean	Returns whether the Air Conditioner Unit is running. (0 for no, 1 for yes)
Mode	Integer	(Unknown) (Returns output in the range 0-2, equivalent to the input of the "Mode" parameter.)
Error	Boolean	Returns whether the Air Conditioner Unit is flashing an error. (0 for no, 1 for yes)
Lock	Boolean	Returns whether the Air Conditioner Unit is locked. (0 for no, 1 for yes)
On	Boolean	Returns whether the Air Conditioner Unit is turned on. (0 for no, 1 for yes)
RequiredPower	Integer	Returns the current amount of power, required by the Air Conditioner, in Watts.

Filtration

Filtration

Operation
Power Usage	10W
Construction
Placed with	Kit (Atmospherics)
Placed on	Small Grid
Stage 1
Deconstruction
Deconstructed with	Hand Drill
Item received	Kit (Atmospherics)

Description

Used to separate gasses from one pipe network into another using filters. Can filter up to two (2) gases at once.

Usage

Place the Kit (Atmospherics) and change the variant to Filtration.
Place filters in the machine for what you want to filter out.
There are three filtration pipe connections.
Filtration Input is where you connect the incoming atmosphere to be passed through the Filtration Atmospherics.
Filtration Unfiltered is the remaining mix after extracting whatever the filters did.
Filtration Filtered is the filtered material for which you placed filters in the machine for.

Be aware that the filtration unit unrealistically has an infinitely powerful pump integrated into its output port. That means as long as it is turned on and there is gas to filter out from the input it will pump that filtered out gas into the output pipe network (no matter how high the pressure in that output pipe network already is!). So eventually that pipe network will burst (around 60 MPa) unless you provide some sort of pop-off valve (e.g. a combination of a back-pressure regulator and a passive vent) or use a pipe analyzer and some logic to turn the filtration unit off when a certain amount of pressure is exceeded in the output pipe network. The filtration system can handle an input gas flow of just over 2.3L from a volume pump.

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters, that can be written to with a Logic Writer, Batch Writer, or Integrated Circuit (IC10). The outputs are listed in the order a Logic Writer's "VAR" setting cycles through them.

Parameter Name	Data Type	Description
On	Boolean	Turns the Filtration Unit on, when set to 1. Turns it off, when set to 0.

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Logic

Output Name	Data Type	Description
Power	Boolean	Returns whether the Filtration Unit is turned on and receives power. (0 for no, 1 for yes)
Error	Boolean	Returns whether the Filtration Unit is flashing an error. (0 for no, 1 for yes)
Lock	Boolean	Returns whether the Filtration Unit is locked. (0 for no, 1 for yes)
Maximum
Mode	Integer	0=Idle, 1=Active
On	Boolean	Returns whether the Filtration Unit is turned on. (0 for no, 1 for yes)
Open	Boolean	Returns whether the Filtration Unit is flashing an error. (0 for no, 1 for yes)
OperationalTemperatureEfficiency
RequiredPower	Integer	Returns the current amount of power, required by the Filtration Unit, in Watts.
PrefabHash	Integer	The Hash of the structure.
PressureEfficiency	Float
CombustionInput
CombustionOutput
CombustionOutput2
PressureInput	Float	the pressure on the input pipe
PressureOutput	Float	the pressure on the filtered output pipe
PressureOutput2	Float	the pressure on the waste output pipe
Ratio	Float
RatioCarbonDioxideInput
RatioCarbonDioxideOutput
RatioCarbonDioxideOutput2
RatioNitrogenInput
RatioNitrogenOutput
RatioNitrogenOutput2
RatioNitrousOxideInput
RatioNitrousOxideOutput
RatioNitrousOxideOutput2
RatioOxygenInput
RatioOxygenOutput
RatioOxygenOutput2
RatioPollutantInput
RatioPollutantOutput
RatioPollutantOutput2
RatioVolatilesInput
RatioVolatilesOuput
RatioVolatilesOuput2
RatioWaterInput
RatioWaterOutput
RatioWaterOutput2
Setting
TemperatureDifferencialEfficiency	Float	a value from 0..1.0 indicating the efficiency based on the temperature differential between the "waste" output and the conditioned air stream. This is not updated while the unit is Idle.
TemperatureInput
TemeratureOutput
TemeratureOutput2
TotalMolesInput
TotalMolesOutput
TotalMolesOutput2

Logic Slots

Slot 0 and 1 are the two gas filters. Slot 2 is the programmable chip

Output Name	Data Type	Description
Occupied	Boolean	Returns whether the slot is occupied. (0 for no, 1 for yes)
OccupantHash	Integer	Returns the hash of the object in the slot.
Quantity	Integer	Returns the current quantity, such as stack size, of the item in the slot.
Damage	Integer	Returns the damage state of the item in the slot.
Class	Integer	Returns an integer representing the class of object.
MaxQuanity	Integer	Returns max stack size of the item in the slot.
PrefabHash	Integer	Returns the hash of the structure in the slot.

Electrolyzer

Electrolyzer

Operation
Power Usage	1200W
Construction
Placed with	Kit (Atmospherics)
Placed on	Small Grid
Stage 1
Deconstruction
Deconstructed with	Hand Drill
Item received	Kit (Atmospherics)

Description

Used to separate water (H₂O) into H₂ and O₂ in a 2 to 1 ratio (perfect fuel).

Usage

Place the Kit (Atmospherics) and change the variant to Electrolyzer.
There are two pipe connections.
Electrolyzer Input is where you connect the incoming water.
Electrolyzer Output is where the H₂ and O₂ comes out mixed together.

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters, that can be written to with a Logic Writer, Batch Writer, or Integrated Circuit (IC10). The outputs are listed in the order a Logic Writer's "VAR" setting cycles through them.

Parameter Name	Data Type	Description
Lock	Boolean	Locks the Electrolyzer , when set to 1. Unlocks it, when set to 0.
On	Boolean	Turns the Electrolyzer on, when set to 1. Turns it off, when set to 0.

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name	Data Type	Description
Power	Boolean	Returns whether the Electrolyzer is turned on and receives power. (0 for no, 1 for yes)
Error	Boolean	Returns whether the Electrolyzer is flashing an error. (0 for no, 1 for yes)
Lock	Boolean	Returns whether the Electrolyzer is locked. (0 for no, 1 for yes)
On	Boolean	Returns whether the Electrolyzer is turned on. (0 for no, 1 for yes)
RequiredPower	Integer	Returns the current amount of power, required by the Electrolyzer, in Watts.

Hydrogen Combustor

The hydrogen combustor takes a fuel mix (H2+O2), and generates water, a *lot* of heat, and waste gasses.

Limiting inflow is *highly* recommended, due to the massive amounts of heat generated.