Unofficial Stationeers Wiki Unofficial Stationeers Wiki

Kit (Consoles)

Properties
Stacks	Yes (5)
Recipe
Created With	Electronics Printer, Fabricator
Cost	2g Iron, 5g Copper, 3g Gold

Console

Operation
Power Usage	50W
Construction
Placed with	Kit (Consoles)
Placed on	Small Grid, On Frames
Stage 1
Next Stage Construction
Constructed with item	Circuitboard
Deconstruction
Deconstructed with	Hand Drill
Item received	Kit (Consoles)
Stage 2
Next Stage Construction
Constructed with item	Glass Sheet
Deconstruction
Item received	Circuitboard
Stage 3
Deconstruction
Deconstructed with	Crowbar
Item received	Glass Sheet

Console

Information

The console is one device of the Console item kit. The console can be fitted with a Circuitboard. When putting in a data disk, the console can be configured after being fully constructed with a circuitboard. After putting out the data disk it runs like previously configured. There is the Console (Variant 1 of the kit) which has a mixed input (data and energy) and the Console Dual (Variant 2 of the kit) which has two inputs (one for energy and one for data).

Example set up

For example one can set it to pressure measurement (requires gas circuit board inside) which allows one to read out the actual pressure value of a connected gas sensor. (Setup shown in picture)

Tips

• You need to insert a Circuit Board and then put a sheet of glass over it to complete construction.
• To display general readings, only the Graph Display Circuit Board will find all the devices which are connected to your power grid. Any available readings will be shown on the select list.
• For other specialized Circuit Boards (Gas, Power, etc.) the only values that can be displayed are those related to the function of that board.

Deconstruction

First remove the glass sheet with a Crowbar. The device itself is deconstructed with the Hand Drill.

Console, Console Dual and Console Monitor

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters that can be written with a Logic Writer, Batch Writer, or Integrated Circuit (IC10).

Parameter Name	Data Type	Description
Open	Boolean	(Unknown)
On	Boolean	Turns the Console on, when set to 1. Turns it off, when set to 0.

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name	Data Type	Description
Power	Boolean	Returns whether the Console is turned on and receives power. (0 for no, 1 for yes)
Open	Boolean	(Unknown)
Error	Boolean	Returns whether the Console is flashing an error. (0 for no, 1 for yes)
On	Boolean	Returns whether the Console is turned on. (0 for no, 1 for yes)
RequiredPower	Integer	Returns the current amount of power required by the Console, in watts.

LED Display (Small, Medium and Large)

Name	Picturne	Placed with
Small display LED		1 - Kit (Consoles)
Medium display LED		2 - Kit (Consoles)
Large display LED		3 - Kit (Consoles)

Data Network Properties

These are all Data Network properties of this device.

Mode Values

These lists the values and meanings for the "Mode" property of the LED Display.

Value	Meaning	"Setting" parameter interpretation
0	Normal number display	Direct display as a number. Values smaller than 1.000E-07 will be displayed as 0.
1	Percentage number display	Input range of 0.0 to 1.0 is interpolated and displayed as the range 0% to 100%
2	Power display	Adds a watt suffix (W) to the number. Also divides the number as needed and adds a metric unit prefix to the suffix. (e.g. kW)

Data Parameters

These are all parameters that can be written with a Logic Writer, Batch Writer, or Integrated Circuit (IC10).

Parameter Name	Data Type	Description
Mode	Integer	Sets the display mode of the LED Display to the passed value. (See Mode Values)
Setting	Float	Sets the raw number to display on the LED Display.
On	Boolean	Turns the LED Display on, when set to 1. Turns it off, when set to 0.
Color	Integer	Sets the color of the text on the LED Display. (See Data Network Colors)

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name	Data Type	Description
Power	Boolean	Returns whether the LED Display is turned on and receives power. (0 for no, 1 for yes)
Mode	Integer	Returns the mode of the LED Display. (See Mode Values)
Error	Boolean	Returns whether the LED Display is flashing an error. (0 for no, 1 for yes)
Setting	Float	Returns the "Setting" value of the LED Display.
On	Boolean	Returns whether the LED Display is turned on. (0 for no, 1 for yes)
RequiredPower	Integer	Returns the current amount of power, required by the LED Display, in watts.
Color	Integer	Returns the color setting of the LED Display. (See Data Network Colors)