Actions

Pressure Regulator

From Unofficial Stationeers Wiki

Revision as of 05:30, 10 July 2024 by Emilgardis (talk | contribs) (add more info in itembox)


Kit (Pressure Regulator)
ItemKitRegulator.png
Constructing Options Pressure Regulator, Back Pressure Regulator, Pressurant Valve, Purge Valve
Properties
Stacks Yes (5)
Recipes
Hydraulic Pipe Bender 5g Iron, 1g Gold, 2g Copper
Logic
Item Hash 1181371795
Item Name ItemKitRegulator
Logic Classes
SlotClass.None
SortingClass.Kits

Construction Kit (Pressure Regulator)

Description

Pressure Regulator is used throughout Atmospherics networks to manage Pressure. Pressure Regulators comes in two variants: Standard and back-pressure regulators. They can be used to regulate the pressure between two pipe networks.

The maximum pressure that can be set is 20265 kPa, which is double the maximum pressure for most gas-related elements like Canisters.

Pressure regulator needs power to operate (100 W).

Use

Use left-click while in active hands to place. Scroll to change to other variants.

Pressure Regulator

Description

The standard Pressure Regulator will pass through gases, in one direction, while the pressure on its output side is below the set value. It combines several functions:

  • Passive check valve: Gas is never allowed to pass "the wrong way", from output to input, even if the Regulator is switched off or unpowered. (It does not allow gas to pass at all when switched off or unpowered)
  • Switched valve: Gas will not pass at all if the Regulator is switched off or unpowered. This is a similar function to the Pipe Digital Valve.
  • Regulator: Gas will only pass when the pressure at the output is below the Regulator's setting.
  • Compressor: While active, the Regulator will move all available gas from input to output, up to the set pressure. (Contrast with, for example, a Pipe Valve which simply equalizes pressure and then stops.)

To calculate the moles per tick, use the following equation: n = (P * V) / (R * T)

Where:

  • P = Min(Input pressure, 101.325)
  • V = (OutputPipeVolume / InputPipeVolume) * 100
  • n = Moles per tick
  • R = Gas constant (8.3144)
  • T = Input temperature

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters that can be written with a Logic Writer, Batch Writer, or Integrated Circuit (IC10).


Parameter Name Data Type Description
Lock Boolean
Setting float
On Boolean

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name Data Type Description
Power Boolean
Error Boolean
Lock Boolean
Setting float Contains the current threshold set on the regulator, in kPa
Maximum float Value of 20265kPa
Ratio Float The ratio between the Setting and the Maximum. As in Ratio = Setting / 20265
On Boolean
Requiredpower Integer In Watts. The Pressure Regulator require 100W of power to function

Back Pressure Regulator

Description

The Back Pressure Regulator variant will only pass through gases when the pressure on its intake side exceeds the set value. In other words, the standard Regulator defaults open and closes when the output is overpressured, while the Back Pressure Regulator defaults closed and opens when the input is overpressured.

Like the standard Regulator, the Back Pressure Regulator also acts as a check valve, switched valve, and compressor (i.e., input gas will move even if the output is already a higher pressure).

Its low flow rate makes it not suitable for being used as an emergency dump valve.

To calculate the moles per tick, use the following equation: n = (P * V) / (R * T)

Where:

  • P = Min(Input pressure, 101.325)
  • V = 100
  • n = Moles per tick
  • R = Gas constant (8.3144)
  • T = Input temperature

Data Network Properties

These are all Data Network properties of this device.

Back Pressure Regulator has exactly the same Network properties as the Pressure Regulator.

Pressurant Valve

Description

(To be spaded)

Purge Valve

Description

Allows for removal of pressurant gas and evaporated liquids from a liquid pipe. Similar in function to a Back Pressure Regulator, the Purge Valve move gas from the input liquid pipe to the output gas pipe, aiming to keep the pressure of the input at the target setting.

(To be spaded)