Unofficial Stationeers Wiki Unofficial Stationeers Wiki

Kit (Elevator)

Constructing Options	Elevator Shaft, Elevator Level
Properties
Stacks	Yes (5)
Recipe
Created With	Electronics Printer, Fabricator
Cost	2g Copper, 4g Gold, 2g Steel, 2g Solder

Description

The elevator allows easy travel to other floors.

Use

Elevators allow easy access to other floors. They operate using two placement types: elevator level for floors where the elevator stops, and elevator shaft for those where they don't.
Logic and enumeration are automatically applied, and the elevator car is created when building a level.

All levels and shafts must face the same direction, so that their spines align..

---

Elevator Shaft

Elevator Shaft

Operation
Power Usage	5W
Construction
Placed with	Kit (Elevator)
Placed on	Large Grid
Stage 1
Deconstruction
Deconstructed with	Hand Drill
Item received	Kit (Elevator)

The shaft section to build on floors it should not open like floor frames etc.
Currently does not require power.

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters that can be written with a Logic Writer, Batch Writer, or Integrated Circuit (IC10).

Parameter Name	Data Type	Description
On	Boolean	Turns the device on, when set >= 1. Turns it off, when set to <1.
Elevatorlevel	Integer	Returns current level carriage is on

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name	Data Type	Description
Power	Boolean	Returns whether the device is turned on and receives power. (0 for no, 1 for yes)
On	Boolean	Returns whether the device is turned on. (0 for no, 1 for yes)
RequiredPower	Integer	Returns the current amount of power, required by the device, in watts.
Elevatorspeed	Integer	Returns 1 going up, 0 standing still and -1 going down
Elevatorlevel	Integer	Returns current level carriage is on

---

Elevator Level

Elevator Level

Operation
Power Usage	5W
Construction
Placed with	Kit (Elevator)
Placed on	Large Grid
Stage 1
Deconstruction
Deconstructed with	Hand Drill
Item received	Kit (Elevator)

The elevator level provides an entrance/exit stop for the elevator car.
Requires power to open the door automatically and use the call button

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters that can be written with a Logic Writer, Batch Writer, or Integrated Circuit (IC10).

Parameter Name	Data Type	Description
Open	Boolean	Opens the device , when set >= 1. Closes it, when set to < 1.
Lock	Boolean	Locks the device , when set >= 1. Unlocks it, when set to <1.
On	Boolean	Turns the device on, when set >= 1. Turns it off, when set to <1.
Elevatorlevel	Integer	Write the level you want the carriage to go to.

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name	Data Type	Description
Power	Boolean	Returns whether the device is turned on and receives power. (0 for no, 1 for yes)
Open	Boolean	Returns whether the device is open. (0 for no, 1 for yes)
Error	Boolean	Returns whether the device is flashing an error. (0 for no, 1 for yes)
Lock	Boolean	Returns whether the device is locked. (0 for no, 1 for yes)
On	Boolean	Returns whether the device is turned on. (0 for no, 1 for yes)
RequiredPower	Integer	Returns the current amount of power, required by the Glass Door, in watts.
ElevatorSpeed	Integer	Returns 1 going up, 0 standing still and -1 going down
ElevatorLevel	Integer	Returns current level carriage is on