Difference between revisions of "Pipes"
From Unofficial Stationeers Wiki
KlingonIAG (talk | contribs) m (<Date mise a jour (19/05/2024"14:59) |
|||
| Line 29: | Line 29: | ||
* Pipes can store some gas inside of them, which can be used with small airlocks to store gas when depressurizing | * Pipes can store some gas inside of them, which can be used with small airlocks to store gas when depressurizing | ||
* Pipes will burst if the pressure differential between the inside pressure and outside atmosphere is greater than 60,795KPa (60MPa) (plus a random check to allow for short bursts over this limit) | * Pipes will burst if the pressure differential between the inside pressure and outside atmosphere is greater than 60,795KPa (60MPa) (plus a random check to allow for short bursts over this limit) | ||
| − | * Pipes will be stressed (make a noise) when the pressure difference between inside and outside the pipe is greater than 48,636kPa. | + | * Pipes will be stressed (make a noise) when the pressure difference between inside and outside the pipe is greater than 48,636kPa. This equals to 80% of the burst pressure. |
| − | * Pipes will also be stressed if a Liquid enters them. | + | * Pipes will also be stressed if a Liquid enters them. <code>Stress in % = 5000 x "liters of liquid" / "pipe network volume"</code> |
* A contiguous pipe (not interrupted by valves, regulators, pumps etc.) of any length, will always have the same pressure, temperature and mixture over its entire length. No matter at what point of the pipe you're introducing new gases into the pipe, they will instantly and evenly "average out" over the entire pipe. | * A contiguous pipe (not interrupted by valves, regulators, pumps etc.) of any length, will always have the same pressure, temperature and mixture over its entire length. No matter at what point of the pipe you're introducing new gases into the pipe, they will instantly and evenly "average out" over the entire pipe. | ||
Revision as of 08:00, 13 September 2024
<Date mise a jour (19/05/2024"14:59)
 | |
| Volume | 10L, 60Mpa |
|---|---|
| Properties | |
| Stacks | Yes, 20 |
| Recipe | |
| Created With | Hydraulic Pipe Bender |
| Cost | 0.5g Iron |
 | |
| Volume | 10L, 60Mpa |
|---|---|
| Properties | |
| Stacks | Yes, 20 |
| Recipe | |
| Created With | Hydraulic Pipe Bender |
| Cost | 1g Silicon, 1g Steel |
Pipes are used to transport gas. Pipes are one of the possible types of inputs/outputs from a structure (the others being Cables, Chutes, and Kit (Liquid Pipe)).
Tips
- Pipes can store some gas inside of them, which can be used with small airlocks to store gas when depressurizing
- Pipes will burst if the pressure differential between the inside pressure and outside atmosphere is greater than 60,795KPa (60MPa) (plus a random check to allow for short bursts over this limit)
- Pipes will be stressed (make a noise) when the pressure difference between inside and outside the pipe is greater than 48,636kPa. This equals to 80% of the burst pressure.
- Pipes will also be stressed if a Liquid enters them.
Stress in % = 5000 x "liters of liquid" / "pipe network volume" - A contiguous pipe (not interrupted by valves, regulators, pumps etc.) of any length, will always have the same pressure, temperature and mixture over its entire length. No matter at what point of the pipe you're introducing new gases into the pipe, they will instantly and evenly "average out" over the entire pipe.
Variations
Can be painted individually or by the stack with Spray Can. (consumes a single 'use' of the can either way, far more efficient to paint a full stack)
Insulated
Insulated pipes stop the exchange of heat between the pipe and it's surrounding environment
Pipes:
Straight
Corner
T-Junction
4-Way Junction
5-Way Junction
6-Way Junction
3-Way Corner
4-Way Corner
Insulated Pipes:
Straight
Corner
T-Junction
4-Way Junction
5-Way Junction
6-Way Junction
3-Way Corner
4-Way Corner
