Editing Power Controller
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
| Latest revision | Your text | ||
| Line 2: | Line 2: | ||
<translate> | <translate> | ||
{{Itembox | {{Itembox | ||
| − | | name = Power Controller | + | | name = Area Power Controller |
| − | | image = [[File:ItemAreaPowerControl.png]] | + | | image = {{{image|[[File:ItemAreaPowerControl.png]]}}} |
| stacks = 5 | | stacks = 5 | ||
| maxinpower = 10W for the APC<br>+ 1000W Battery Charging<br>+ Output Load | | maxinpower = 10W for the APC<br>+ 1000W Battery Charging<br>+ Output Load | ||
| Line 10: | Line 10: | ||
| cost = 5g [[Iron]], 2g [[Copper]], 3g [[Solder]] | | cost = 5g [[Iron]], 2g [[Copper]], 3g [[Solder]] | ||
}} | }} | ||
| − | {{ | + | {{structurebox |
| − | | name | + | | name = Area Power Controller |
| − | | | + | | dectool = [[Hand Drill]] |
| − | + | | powerusage = 10W | |
| − | | | + | | placement = Small Grid |
| − | | | ||
| − | |||
}} | }} | ||
== Description == <!--T:1--> | == Description == <!--T:1--> | ||
| Line 22: | Line 20: | ||
== Usage == <!--T:2--> | == Usage == <!--T:2--> | ||
| − | The APC can be opened with a [[Crowbar]], once opened the switch must be set to the 'ON' state for it to function. A [[Battery Cell]] can be added to act as a power buffer for the subnetwork in the event the main power network gets disconnected. | + | The APC can be opened with a [[Crowbar]], once opened the switch must be set to the 'ON' state for it to function. A [[Battery Cell]] can be added to act as a power buffer for the subnetwork in the event the main power network gets disconnected. Currently, the dials in the APC do nothing. |
<br><br> | <br><br> | ||
| − | The APC can generally be used for machines with varying power requirements such as the Auto lathe, Electronics Printer, Fabricator, Arc Furnace, and more. This will allow all these machines to take lots of power in short intervals as long as the APC has a battery. | + | The APC can generally be used for machines with varying power requirements such as the Auto lathe, Electronics Printer, Fabricator, Arc Furnace, and more. This will allow all these machines to take lots of power in short intervals as long as the APC has a battery. This is a similar object to the [[Transformer]] that only allows a specified amount of power through. |
If sufficient power is available upstream, the APC acts as a pass through and will not limit it's output power, it is recommended to use a [[Fuse|Cable Fuse]] or [[Transformer|Transformer (Small)]] when powering a non-heavy cable network to prevent overdraw. | If sufficient power is available upstream, the APC acts as a pass through and will not limit it's output power, it is recommended to use a [[Fuse|Cable Fuse]] or [[Transformer|Transformer (Small)]] when powering a non-heavy cable network to prevent overdraw. | ||
| − | + | == Logic Properties == | |
| + | These are all logic properties of this device. There is no difference in parameters, whether the logic network is connected to the input or output of the Area Power Control. | ||
=== Mode Values === | === Mode Values === | ||
| Line 36: | Line 35: | ||
! Value !! Display !! Meaning | ! Value !! Display !! Meaning | ||
|- | |- | ||
| − | | 0 || Grey || | + | | 0 || Grey || No output power draw or the Area Power Control is turned off. |
|- | |- | ||
| 1 || Red || No battery in the Area Power Control and there is power drawn from the output. | | 1 || Red || No battery in the Area Power Control and there is power drawn from the output. | ||
| Line 45: | Line 44: | ||
|- | |- | ||
| 4 || Green || There is a battery in the Area Power Control, the output draw is less than the input and the battery is fully charged. | | 4 || Green || There is a battery in the Area Power Control, the output draw is less than the input and the battery is fully charged. | ||
| + | |- | ||
| + | | 5 || Grey || (Unknown) | ||
|} | |} | ||
| − | + | === Logic Parameters === | |
| + | These are all parameters, that can be written to with a [[Kit_(Logic_I/O)#Logic_Writer|Logic Writer]] or a [[Kit_(Logic_I/O)#Batch_Writer|Batch Writer]]. The outputs are listed in the order a Logic Writer's "VAR" setting cycles through them. | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
| Line 61: | Line 63: | ||
|} | |} | ||
| − | + | === Logic Outputs === | |
| + | These are all parameters, that can be read with a [[Kit_(Logic_I/O)#Logic_Reader|Logic Reader]]. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them. | ||
{| class="wikitable" | {| class="wikitable" | ||
|- | |- | ||
| Line 92: | Line 95: | ||
== History == <!--T:3--> | == History == <!--T:3--> | ||
| − | + | Previously in older versions of the game, a battery must be placed in the APC for it to function. This is no longer the case after the power rework update in v0.1.1062.5426. | |
| − | |||
| − | |||
| + | You DO NOT need a battery in the APC for it to function. I suggest that you have a battery in the APC, as a buffer. v0.1.1143.5721. | ||
</translate> | </translate> | ||