Editing Combustion Centrifuge
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 4: | Line 4: | ||
[[Category:Machines]] | [[Category:Machines]] | ||
{{Itembox | {{Itembox | ||
− | | image = [[File: | + | | image = [[File:ItemKitCombustionCentrifuge.png]] |
| name = Kit (Combustion Centrifuge) | | name = Kit (Combustion Centrifuge) | ||
| createdwith = [[Autolathe]] (Tier 2) | | createdwith = [[Autolathe]] (Tier 2) | ||
Line 19: | Line 19: | ||
| item_rec1 = [[Kit (Combustion Centrifuge)]] | | item_rec1 = [[Kit (Combustion Centrifuge)]] | ||
| const_with_tool2 = [[Welder]] | | const_with_tool2 = [[Welder]] | ||
− | | const_with_item2 = 2x [[Steel | + | | const_with_item2 = 2x [[Steel Sheet]] |
| stage_image2 = [[File:StructureCombustionCentrifuge_BuildState1.png]] | | stage_image2 = [[File:StructureCombustionCentrifuge_BuildState1.png]] | ||
| decon_with_tool2 = [[Angle Grinder]] | | decon_with_tool2 = [[Angle Grinder]] | ||
− | | item_rec2 = 2x [[Steel | + | | item_rec2 = 2x [[Steel Sheet]] |
| const_with_item3 = 1x [[Cable Coil]] | | const_with_item3 = 1x [[Cable Coil]] | ||
| decon_with_tool3 = [[Wire Cutters]] | | decon_with_tool3 = [[Wire Cutters]] | ||
Line 29: | Line 29: | ||
== Description == <!--T:2--> | == Description == <!--T:2--> | ||
− | The combustion centrifuge is a gas powered version of the [[Centrifuge]]. A combustible fuel mix should be supplied to the gas input, and waste gasses should be vented from the output. The machine's RPM's must be controlled via the throttle and combustion limiter levers. If the Combustion Centrifuge gains, or | + | The combustion centrifuge is a gas powered version of the [[Centrifuge]]. A combustible fuel mix should be supplied to the gas input, and waste gasses should be vented from the output. The machine's RPM's must be controlled via the throttle and combustion limiter levers. If the Combustion Centrifuge gains, or looses, RPMs too fast it will experience stress, and eventually grind to a halt. Higher RPMs directly result in faster processing speeds. |
The throttle lever controls the amount of fuel being pulled into the machine, increasing the temperature inside the engine, and leading to an increase in RPM. The limiter lever influences the speed of combustion, and how much uncombusted gas is in the exhaust. | The throttle lever controls the amount of fuel being pulled into the machine, increasing the temperature inside the engine, and leading to an increase in RPM. The limiter lever influences the speed of combustion, and how much uncombusted gas is in the exhaust. | ||
Line 36: | Line 36: | ||
The Combustion Centrifuge has a socket for an [[Integrated Circuit (IC10)|IC10 chip]], similar to the [[Atmospherics]] machine. It comes with two device ports, d0 and d1, for connecting to other devices. To change or set a device, use a screwdriver to cycle through devices found on the machine's data network. | The Combustion Centrifuge has a socket for an [[Integrated Circuit (IC10)|IC10 chip]], similar to the [[Atmospherics]] machine. It comes with two device ports, d0 and d1, for connecting to other devices. To change or set a device, use a screwdriver to cycle through devices found on the machine's data network. | ||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
− | |||
{{Data Network Header}} | {{Data Network Header}} | ||
Line 78: | Line 69: | ||
|- | |- | ||
| Temperature || Integer || The current temperature reading of the device | | Temperature || Integer || The current temperature reading of the device | ||
− | |||
− | |||
|- | |- | ||
| RatioOxygen || Float || The ratio of oxygen in device atmosphere | | RatioOxygen || Float || The ratio of oxygen in device atmosphere |