Actions

Editing Pipes

Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.

The edit can be undone. Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision Your text
Line 8: Line 8:
 
  | cost        = 0.5g [[Iron]]
 
  | cost        = 0.5g [[Iron]]
 
  | stacks      = Yes, 20
 
  | stacks      = Yes, 20
−
  | volume      = 10L, 60Mpa
+
  | volume      = 100L, 60Mpa
−
  | createdwith = [[Hydraulic Pipe Bender]]
+
  | createdwith = [[Hydraulic Pipe Bender]], [[Hydraulic Pipe Bender Mk. II]]
−
}}
 
−
{{Itembox
 
−
| name        = Kit (Insulated Pipe)
 
−
| image      = [[File:{{#setmainimage:ItemKitInsulatedPipe.png}}]]
 
−
| cost        = 1g [[Silicon]], 1g [[Steel]]
 
−
| stacks      = Yes, 20
 
−
| volume      = 10L, 60Mpa
 
−
| createdwith = [[Hydraulic Pipe Bender]]
 
 
}}
 
}}
  
−
 
+
Pipes are used to transport gas. Pipes are one of the possible types of inputs/outputs from a structure (the others being [[Cables]] and [[Chutes]]).
−
Pipes are used to transport gas. Pipes are one of the possible types of inputs/outputs from a structure (the others being [[Cables]], [[Chutes]], and [[Kit (Liquid Pipe)]]).
 
  
 
=== Tips === <!--T:2-->
 
=== Tips === <!--T:2-->
Line 29: Line 20:
 
* Pipes will burst if the pressure differential between the inside pressure and outside atmosphere is greater than 60,795KPa (60MPa) (plus a random check to allow for short bursts over this limit)
 
* Pipes will burst if the pressure differential between the inside pressure and outside atmosphere is greater than 60,795KPa (60MPa) (plus a random check to allow for short bursts over this limit)
 
* Pipes will be stressed (make a noise) when the pressure difference between inside and outside the pipe is greater than 48,636kPa.
 
* Pipes will be stressed (make a noise) when the pressure difference between inside and outside the pipe is greater than 48,636kPa.
−
* Pipes will also be stressed if a Liquid enters them. (further research required as to when)
 
 
* A contiguous pipe (not interrupted by valves, regulators, pumps etc.) of any length, will always have the same pressure, temperature and mixture over its entire length. No matter at what point of the pipe you're introducing new gases into the pipe, they will instantly and evenly "average out" over the entire pipe.
 
* A contiguous pipe (not interrupted by valves, regulators, pumps etc.) of any length, will always have the same pressure, temperature and mixture over its entire length. No matter at what point of the pipe you're introducing new gases into the pipe, they will instantly and evenly "average out" over the entire pipe.
  
 
==Variations== <!--T:3-->
 
==Variations== <!--T:3-->
 
Can be painted individually or by the stack with [[Spray Can]]. (consumes a single 'use' of the can either way, far more efficient to paint a full stack)
 
Can be painted individually or by the stack with [[Spray Can]]. (consumes a single 'use' of the can either way, far more efficient to paint a full stack)
−
 
−
===Insulated===
 
−
Insulated pipes stop the exchange of heat between the pipe and it's surrounding environment
 
  
 
Pipes:
 
Pipes:
 
<gallery mode='traditional'>
 
<gallery mode='traditional'>
−
Image: ItemPipeStraight.png       | Straight  
+
Image:ItemPipeStraight.png|Straight  
−
Image: ItemPipeCorner.png         | Corner
+
Image:ItemPipeCorner.png| Corner
−
Image: ItemPipeTJunction.png     | T-Junction
+
Image:ItemPipeCrossJunction3.png| 3-Way Corner
−
Image: ItemPipeCrossJunction.png | 4-Way Junction
+
Image:ItemPipeTJunction.png| T-Junction
−
Image: ItemPipeCrossJunction5.png | 5-Way Junction
+
Image:ItemPipeCrossJunction.png| 4-Way Junction
−
Image: ItemPipeCrossJunction6.png | 6-Way Junction
+
Image:ItemPipeCrossJunction5.png|5-Way Junction
−
Image: ItemPipeCrossJunction3.png | 3-Way Corner
+
Image:ItemPipeCrossJunction6.png| 6-Way Junction
−
Image: ItemPipeCrossJunction4.png | 4-Way Corner
 
 
</gallery>
 
</gallery>
 
Insulated Pipes:
 
Insulated Pipes:
 
<gallery mode='traditional'>
 
<gallery mode='traditional'>
−
Image: ItemInsulatedPipeStraight.png      | Straight  
+
Image:Item|Straight  
−
Image: ItemInsulatedPipeCorner.png        | Corner
+
Image:Item| Corner
−
Image: ItemInsulatedPipeTJunction.png      | T-Junction
+
Image:Item| 3-Way Corner
−
Image: ItemInsulatedPipeCrossJunction.png  | 4-Way Junction
+
Image:Item| T-Junction
−
Image: ItemInsulatedPipeCrossJunction5.png | 5-Way Junction
+
Image:Item| 4-Way Junction
−
Image: ItemInsulatedPipeCrossJunction6.png | 6-Way Junction
+
Image:Item|5-Way Junction
−
Image: ItemInsulatedPipeCrossJunction3.png | 3-Way Corner
+
Image:Item| 6-Way Junction
−
Image: ItemInsulatedPipeCrossJunction4.png | 4-Way Corner
 
 
</gallery>
 
</gallery>
  
 
</translate>
 
</translate>

Please note that all contributions to Unofficial Stationeers Wiki may be edited, altered, or removed by other contributors. If you do not want your writing to be edited mercilessly, then do not submit it here.
You are also promising us that you wrote this yourself, or copied it from a public domain or similar free resource (see Unofficial Stationeers Wiki:Copyrights for details). Do not submit copyrighted work without permission!

To edit this page, please answer the question that appears below (more info):

Cancel | Editing help (opens in new window)

Templates used on this page:

Retrieved from "https://stationeers-wiki.com/Pipes"