Editing Guide (Airlock) Atmosphere to Atmosphere
Warning: You are not logged in. Your IP address will be publicly visible if you make any edits. If you log in or create an account, your edits will be attributed to your username, along with other benefits.
The edit can be undone.
Please check the comparison below to verify that this is what you want to do, and then save the changes below to finish undoing the edit.
Latest revision | Your text | ||
Line 32: | Line 32: | ||
# Using the [[Labeller]], rename each portal as "Interior-Door" and "Exterior-Door" appropriately. | # Using the [[Labeller]], rename each portal as "Interior-Door" and "Exterior-Door" appropriately. | ||
# Ensure the "Exterior-Door" is OPEN, and the "Interior-Door" is CLOSED. | # Ensure the "Exterior-Door" is OPEN, and the "Interior-Door" is CLOSED. | ||
− | # Enclose the | + | # Enclose the six remaining sides of the airlock chamber with airtight [[Frames]], [[Walls]], or [[Windows]]. |
# Place [[Console]], [[Active Vent]]s, [[Gas Sensor]], and optional [[Flashing Light]] and [[Power Controller]] somewhere within the airlock's interior. | # Place [[Console]], [[Active Vent]]s, [[Gas Sensor]], and optional [[Flashing Light]] and [[Power Controller]] somewhere within the airlock's interior. | ||
# Ensure all placed devices are attached to the same [[Wire Network]] including the portals' power and data ports. | # Ensure all placed devices are attached to the same [[Wire Network]] including the portals' power and data ports. | ||
Line 41: | Line 41: | ||
# Insert [[Circuitboard (Advanced Airlock)]] into the console, then place the [[Glass Sheet]] onto the console. | # Insert [[Circuitboard (Advanced Airlock)]] into the console, then place the [[Glass Sheet]] onto the console. | ||
# Insert [[Data Disk]] into the side slot of Console then power on the Console.[[File:Guide adv airlock config0.png|thumb|slot to insert data disk]] | # Insert [[Data Disk]] into the side slot of Console then power on the Console.[[File:Guide adv airlock config0.png|thumb|slot to insert data disk]] | ||
− | |||
# Use the console's up and down arrows to scroll through the list of devices. Click to select. Click again to deselect if incorrect | # Use the console's up and down arrows to scroll through the list of devices. Click to select. Click again to deselect if incorrect | ||
# Find and click "Exterior-Door" followed by all caps and green "EXTERIOR". NOTE: SELECT THIS FIRST![[File:Guide adv airlock config1.png|thumb|make sure to click the exterior door and vent first]] | # Find and click "Exterior-Door" followed by all caps and green "EXTERIOR". NOTE: SELECT THIS FIRST![[File:Guide adv airlock config1.png|thumb|make sure to click the exterior door and vent first]] | ||
Line 78: | Line 77: | ||
A depressurization phase will stall if a complete vacuum cannot be achieved within the [[Large Grid Atmosphere|Large Grid Volume]]s in which all selected [[Gas Sensor]]s reside. Such stalled depressurization can be skipped by clicking the yellow "Cancel Depressurize" button on a console, but atmospheric mixing may occur. In larger airlocks, ensure there is one Gas Sensor per Large Grid to prevent premature repressurization and the resulting mixture of interior and exterior atmospheres. | A depressurization phase will stall if a complete vacuum cannot be achieved within the [[Large Grid Atmosphere|Large Grid Volume]]s in which all selected [[Gas Sensor]]s reside. Such stalled depressurization can be skipped by clicking the yellow "Cancel Depressurize" button on a console, but atmospheric mixing may occur. In larger airlocks, ensure there is one Gas Sensor per Large Grid to prevent premature repressurization and the resulting mixture of interior and exterior atmospheres. | ||
− | |||
− | |||
==See Also== | ==See Also== |