Actions

Difference between revisions of "Atmospherics"

From Unofficial Stationeers Wiki

m (prepare future redirect)
m
Line 78: Line 78:
 
Used to filter out specific gasses and fluids from a mixture.<br>
 
Used to filter out specific gasses and fluids from a mixture.<br>
 
it can filter out up to 2 things at once
 
it can filter out up to 2 things at once
 +
Pumps filter gasses through itself.
  
 
==Usage==
 
==Usage==

Revision as of 17:01, 30 November 2019

Kit (Atmospherics)
ItemKitAtmospherics.png
Stacks no
Recipe
Created With Hydraulic Pipe Bender, Fabricator
Cost 10g Iron, 5g Gold, 20g Copper

Air Conditioner Unit

Air Conditioner
Atmospherics front.jpg
Operation
Power Usage Up to 7000W based on temperature difference
Construction
Placed with Kit (Atmospherics)
Placed on Small Grid
Stage 1
Deconstruction
Deconstructed with Hand Drill
Item received Kit (Atmospherics)

Description

Used to lower and raise the temperature fed through it from the input pipe.
It has a range from -99 to 99 Celsius for the output

If the coolant pipe does not have 100kpa pressure it will divert output to coolant waste port to fill its coolant pipe

Usage

Place the Kit (Atmospherics) and run some pipes to the place you want to vent the heat. Place a few Pipe Radiators on the pipe, fill it with whatever gas mixture you want.
Make a return loop on the coolant system back to the coolant waste port for slightly better efficiency.
It will try to draw or expel heat to the coolant mix to make the input match the desired output. See the diagram for an example
Example A/C Setup

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters, that can be written to with a Logic Writer, Batch Writer, or Integrated Circuit (IC10). The outputs are listed in the order a Logic Writer's "VAR" setting cycles through them.

Parameter Name Data Type Description
Open Boolean Starts the Air Conditioner Unit, when set to 1. Stops it, when set to 0. (This seems to work only with Batch Writer and not with Logic Writer - tested on game ver: v0.1.1362.6552).
Mode Integer (Unknown) (Judging by the "Mode" output, it accepts values in the range 0-2.)
Lock Boolean Locks the Air Conditioner Unit, when set to 1. Unlocks it, when set to 0.
On Boolean Turns the Air Conditioner Unit on, when set to 1. Turns it off, when set to 0.

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name Data Type Description
Power Boolean Returns whether the Air Conditioner Unit is turned on and receives power. (0 for no, 1 for yes)
Open Boolean Returns whether the Air Conditioner Unit is running. (0 for no, 1 for yes)
Mode Integer (Unknown) (Returns output in the range 0-2, equivalent to the input of the "Mode" parameter.)
Error Boolean Returns whether the Air Conditioner Unit is flashing an error. (0 for no, 1 for yes)
Lock Boolean Returns whether the Air Conditioner Unit is locked. (0 for no, 1 for yes)
On Boolean Returns whether the Air Conditioner Unit is turned on. (0 for no, 1 for yes)
RequiredPower Integer Returns the current amount of power, required by the Air Conditioner, in Watts.

Filtration

Filtration
Operation
Power Usage 5w
Construction
Placed with Kit (Atmospherics)
Placed on Small Grid
Stage 1
Deconstruction
Deconstructed with Hand Drill
Item received Kit (Atmospherics)

Description

Used to filter out specific gasses and fluids from a mixture.
it can filter out up to 2 things at once Pumps filter gasses through itself.

Usage

Place the Kit (Atmospherics) and change the variant to Filtration.
Place filters in the machine for what you want to filter out.
There are three filtration pipe connections.
Filtration Input is where you connect the incoming atmosphere to be passed through the Filtration Atmospherics.
Filtration Waste is the remaining mix after extracting whatever the filters did.
Filtration Output is the filtered material for which you placed filters in the machine for.

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters, that can be written to with a Logic Writer, Batch Writer, or Integrated Circuit (IC10). The outputs are listed in the order a Logic Writer's "VAR" setting cycles through them.

Parameter Name Data Type Description
On Boolean Turns the Filtration Unit on, when set to 1. Turns it off, when set to 0.

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name Data Type Description
Power Boolean Returns whether the Filtration Unit is turned on and receives power. (0 for no, 1 for yes)
Error Boolean Returns whether the Filtration Unit is flashing an error. (0 for no, 1 for yes)
On Boolean Returns whether the Filtration Unit is turned on. (0 for no, 1 for yes)
RequiredPower Integer Returns the current amount of power, required by the Filtration Unit, in Watts.
Quantity Integer Returns the current amount of Filter remaining. Slot 0(Right), slot 1(left).

Electrolyzer

Electrolyzer
Electrolyzer front.png
Operation
Power Usage 1200W
Construction
Placed with Kit (Atmospherics)
Placed on Small Grid
Stage 1
Deconstruction
Deconstructed with Hand Drill
Item received Kit (Atmospherics)

Description

Used to separate water (H2O) into H2 and O2 in a 2 to 1 ratio (perfect fuel).

Usage

Place the Kit (Atmospherics) and change the variant to Electrolyzer.
There are two pipe connections.
Electrolyzer Input is where you connect the incoming water.
Electrolyzer Output is where the H2 and O2 comes out mixed together.

Data Network Properties

These are all Data Network properties of this device.

Data Parameters

These are all parameters, that can be written to with a Logic Writer, Batch Writer, or Integrated Circuit (IC10). The outputs are listed in the order a Logic Writer's "VAR" setting cycles through them.

Parameter Name Data Type Description
Lock Boolean Locks the Electrolyzer , when set to 1. Unlocks it, when set to 0.
On Boolean Turns the Electrolyzer on, when set to 1. Turns it off, when set to 0.

Data Outputs

These are all parameters, that can be read with a Logic Reader or a Slot Reader. The outputs are listed in the order a Logic Reader's "VAR" setting cycles through them.

Output Name Data Type Description
Power Boolean Returns whether the Electrolyzer is turned on and receives power. (0 for no, 1 for yes)
Error Boolean Returns whether the Electrolyzer is flashing an error. (0 for no, 1 for yes)
Lock Boolean Returns whether the Electrolyzer is locked. (0 for no, 1 for yes)
On Boolean Returns whether the Electrolyzer is turned on. (0 for no, 1 for yes)
RequiredPower Integer Returns the current amount of power, required by the Electrolyzer, in Watts.